Lab 8

Layout and Verification

Generate the layout of the course OTA, check it with DRC and LVS, find errors from the reports, extract it and compare the post-layout simulation with the schematic.

Contents
Lab 8 at a glance  
Goal Generate the layout of the course OTA, check it with DRC and LVS, find errors from the reports, extract it and compare the post-layout simulation with the schematic.
Reproduces Chapter 15 (Figure 15.4, Table 15.4) and Chapter 16 (Tables 16.1 and 16.2, Figure 16.2)
Time 3–4 hours
Files labs/lab8: ota2s.gds, ota2s_lvs.spice, ota2s_pex.spice, ota2s.sch and ota2s.sym, ota2s_pex.sym, postlayout_tb.sch per PDK; tools/layout

Hand calculation

Size the two passives of the OTA from the PDK values of Chapter 15. The Miller capacitor is 1 pF: how large is a square MIM capacitor at 1.5 fF/µm² (SG13G2) or 2.0 fF/µm² (SKY130)? The nulling resistor is 2.1 kΩ (SG13G2, rppd, 260 Ω/sq, 1 µm wide) or 2.6 kΩ (SKY130, res_high_po_0p69, 319.8 Ω/sq, 0.69 µm wide): how long is it without its contact heads? Compare with the drawn sizes in Table 15.4 and explain the difference.

Steps

  1. Generate the layout (or use the copy in labs/lab8/<pdk>). From the top of the course files (art_of_aicd/), run the three commands of Section 15.8: the PDK generators draw the unit cells, then python3 tools/layout/ota_layout.py sg13g2 sky130 places and routes them. Open the result with klayout tools/layout/sg13g2/ota2s.gds & and find the three groups, the guard rings, the Metal3 spines and \(R_z\) and \(C_c\) of Figure 15.4. In SKY130, open it in Magic as well (gds read, load ota2s) and select a few nets.
  2. DRC. Run the commands of Section 16.2 for your PDK, or all checks at once with python3 tools/layout/verify.py (it writes tools/layout/<pdk>/verify.json). Load the report into KLayout with -m and look at the categories, even if they are empty.
  3. LVS. Run the LVS of Section 16.3 against ota2s_lvs.spice. Read the reference netlist first: find the PDK resistor and capacitor and the three dummy lines.
  4. Break it, twice. Copy ota2s_lvs.spice, delete the three dummy lines (MD1–MD3) and run LVS against the copy. Then restore them and swap inp and inn on the gates of M1 and M2. Note what each tool reports.
  5. Extract. Run the Magic extraction of Section 16.4 (or take ota2s_pex.spice from step 2). Find the five largest capacitors and the nets they sit on.
  6. Post-layout simulation. In labs/lab8/<pdk>, run ../../sim.sh postlayout_tb.sch. Copies a and t are the schematic OTA, copies b and u the extracted layout through ota2s_pex.sym, whose spice_sym_def attribute includes ota2s_pex.spice instead of a schematic. The testbench prints the loop gain, phase margin, slew rates and overshoot of both.

Checkpoint

Table 18.9. Lab 8 results (IIC-OSIC-TOOLS 2026.10; post-layout values for the unity-gain buffer with 2 pF, tt, 27 °C).

Quantity SG13G2 SKY130
Layout size 118.8 × 56.6 µm = 6725 µm² 58.9 × 66.4 µm = 3911 µm²
DRC 0 violations (KLayout, all rules except density); antenna: 0 0 violations (KLayout); Magic drc(full): 1 (rpm.1, Section 16.2)
LVS netlists match circuits match uniquely
Without the dummies in the reference FAIL: no match Netlists do not match: 12 devices against 10
With inp and inn swapped FAIL (strict port mode) top level cell failed pin matching
Extracted: devices (fingers), wiring capacitors, total 92, 36, 169 fF 50, 33, 144 fF
Largest extracted capacitor tail to vss, 70 fF between the Miller-capacitor nets, 43 fF
Unity-gain frequency, schematic → layout 21.5 → 21.0 MHz 21.7 → 20.6 MHz
Phase margin, schematic → layout 67.0 → 65.3° 72.8 → 72.4°
Falling slew rate, schematic → layout 15.6 → 14.7 V/µs 14.6 → 13.7 V/µs

Questions

  • The swapped inputs still give a circuit that is topologically the same as the layout. Why does LVS catch it anyway, and what would happen without pin labels on the layout?
  • The SKY130 extraction puts 43 fF in parallel with \(C_c\). Where in Figure 15.4 does it come from, and how would you reduce it?
  • Neither extraction contains the trench stress of Section 15.5. Which device pairs of the OTA would suffer most if their units had different surroundings, and how does the floorplan prevent it?

Extension

Generate the input pair as AABB instead of ABBA with python3 tools/layout/ota_layout.py <pdk> --pair=AABB --out=/tmp/aabb (the default layout stays untouched), run DRC and LVS on /tmp/aabb/<pdk>/ota2s.gds, and confirm that both still pass: LVS checks the circuit, not its sensitivity to gradients. Then use Section 15.4 to estimate the systematic offset the new arrangement would have under a threshold gradient of your choice, and compare it with the random offset of Lab 7. If you have time, place the OTA in a Tiny Tapeout analog tile for your PDK and run the full DRC with density checks, as Chapter 17 suggests.


Back to top

SkillSurf · The Art of Analog IC Design, draft v0.1 (November 2026). Every source is listed on the References page.

© 2025–2026 SkillSurf. Text, figures and 3D models: CC BY 4.0; code: MIT. The SkillSurf name and logo are not covered.

This course was written with the help of AI tools and may contain mistakes. If you find one, please tell us through SkillSurf or email skillsurfedu@gmail.com, and we will correct it.

This site uses Just the Docs, a documentation theme for Jekyll.