Lab 3

The Common-Source Amplifier

Compare the three loads of the common-source stage, see why a high-gain stage has no output bias of its own, and measure its poles, its zero and what a cascode does to them.

Contents
Lab 3 at a glance  
Goal Compare the three loads of the common-source stage, see why a high-gain stage has no output bias of its own, and measure its poles, its zero and what a cascode does to them.
Reproduces Chapter 7 (Sections 7.1–7.2, Figures 7.1 and 7.3) and Chapter 9 (Worked example 9.1, Sections 9.6–9.7, Figure 9.9)
Time 3 hours
Files labs/lab3: cs_loads_tb, cs_mirror_tb, cs_ac_tb, cs_pz_tb, cascode_r_tb, cascode_i_tb (.sch) per PDK

Hand calculation

With \(M_1\) of Worked example 6.1 at \(g_m/I_D\) = 15: (a) the gain of the diode-loaded stage from Eq. (7.4), with the load at 5 V⁻¹; (b) the gain of the current-source-loaded stage from Eq. (7.5), with \(g_{ds1}\) = 20.6 µS and \(g_{ds2}\) = 3.0 µS (SG13G2) or 14.7 µS and 1.15 µS (SKY130); (c) the dominant pole of the stage driven from 20 kΩ, \(f_{p1} \approx 1/(2\pi b_1)\), with \(b_1\) from Worked example 9.1.

Steps

  1. Three loads. Run ../../sim.sh cs_loads_tb.sch. The three stages of Figure 7.1(a)–(c) share one input sweep; the testbench prints the gain of each at its bias point and the output range over which the current-source load keeps half its gain. In the GUI, plot ga vs v(out_r) gb vs v(out_d) gc vs v(out_c) draws Figure 7.3.
  2. A real current source. cs_mirror_tb.sch replaces the ideal \(V_{BP}\) by a diode-connected PMOS carrying 41.9 µA, at the input voltage that put the ideal stage at \(V_{DD}/2\). Run it and note where the output goes, and how far it moves for 1 % more reference current and for 1 mV more input.
  3. Frequency response. Run ../../sim.sh cs_ac_tb.sch: the stage of Worked example 9.1, driven from 20 kΩ into 2 pF, with the DC servo. It prints the DC gain, the −3 dB and unity-gain frequencies and the phase lag at \(f_u\), and the gate voltage the servo found.
  4. Poles and zeros. cs_pz_tb.sch is the same circuit with the servo replaced by that gate voltage, because pz cannot handle the servo’s 1 F capacitor. Run it; print all lists every pole and zero in rad/s as real,imaginary pairs. Divide by 2π and discard the pairs that coincide and the poles far above \(f_T\) (the pitfall of Section 9.7).
  5. Cascode. cascode_r_tb.sch puts the CS stage and a cascode with the same devices side by side with a resistive load, \(R_S\) = 50 kΩ and 50 fF; cascode_i_tb.sch does the same with ideal 41.9 µA loads, 20 kΩ and 2 pF. Each stage has its own servo, so both carry exactly 41.9 µA. Run both and compare the bandwidths and gains.

Checkpoint

Table 18.4. Lab 3 results (tt, 27 °C).

Quantity SG13G2 SKY130
Gain with resistor / diode / current-source load 7.00 / 2.65 / 26.8 10.16 / 2.65 / 39.3
Output range with at least half the gain (current-source load) 0.15–1.02 V 0.28–1.58 V
cs_mirror_tb: output with the mirror instead of \(V_{BP}\) 0.642 V (ideal: 0.600 V) 0.897 V (ideal: 0.900 V)
Output change for 1 % more \(I_{REF}\) / 1 mV more input +18.0 / −27.2 mV +26.3 / −39.0 mV
\(R_S\) = 20 kΩ, 2 pF: DC gain, \(f_{-3\mathrm{dB}}\), \(f_u\), phase lag at \(f_u\) 29.97, 1.546 MHz, 42.2 MHz, 113° 42.39, 1.158 MHz, 49.1 MHz, 91°
pz: poles; right-half-plane zero 1.546 and 93.6 MHz; 3.05 GHz 1.158 MHz and 1.245 GHz; 41.4 GHz
Resistive load, 50 kΩ, 50 fF: \(f_{-3\mathrm{dB}}\) CS → cascode 18.5 → 28.3 MHz 99.2 → 125.7 MHz
Ideal load, 20 kΩ, 2 pF: DC gain, \(f_u\), CS → cascode 30.0 → 512, 42.2 → 41.5 MHz 42.4 → 1019, 49.1 → 47.6 MHz

Questions

  • The diode-loaded gain is 2.65 in both PDKs, the current-source-loaded gain differs by 50 %. Why does the process cancel out of one and not the other?
  • The mirror moves the SG13G2 output by 42 mV but the SKY130 output by only 3 mV. The mirror’s reference and output devices have the same size and current; what differs between them, and why does it matter more in SG13G2 (think of Section 8.2)?
  • With the ideal load the cascode raises the gain 17 to 24 times but does not change \(f_u\). With the resistive load it raises the bandwidth instead. Explain both with the time constants of Section 9.4.
  • Why does pz report a right-half-plane zero at \(g_m/(2\pi C_{dg})\) and not at \(g_m/(2\pi C_{gd})\), and which one did your simulation give?

Extension

In cs_mirror_tb.sch, double the length of both PMOS devices (keep \(W/L\)) and repeat step 2: does the 1 % sensitivity change, and does the systematic shift of the output? Then rerun cs_ac_tb.sch with \(R_S\) = 1 kΩ and 200 kΩ and compare the poles with the dominant-pole estimate of Figure 9.5.


Back to top

SkillSurf · The Art of Analog IC Design, draft v0.1 (November 2026). Every source is listed on the References page.

© 2025–2026 SkillSurf. Text, figures and 3D models: CC BY 4.0; code: MIT. The SkillSurf name and logo are not covered.

This course was written with the help of AI tools and may contain mistakes. If you find one, please tell us through SkillSurf or email skillsurfedu@gmail.com, and we will correct it.

This site uses Just the Docs, a documentation theme for Jekyll.