Appendix D
Glossary
The terms and abbreviations of the course, each with the chapter that introduces it.
A B C D E F G H I J K L M N O P Q R S T U V W X
A
- Acquisition time
- The time a track-and-hold needs, after its switch closes, for the held voltage to settle to the input: about \(N\ln 2\) time constants \(R_{on}C_H\) for N bits. Ch. 19
- Active area
- The region of the silicon surface not covered by trench oxide, where transistors and taps are made (Activ in SG13G2, diff and tap in SKY130). Ch. 15
- ADC (analog-to-digital converter)
- A circuit that samples a voltage and outputs the number of the reference level it falls into, a code of N bits. Flash, SAR, pipelined and delta-sigma ADCs differ in how many comparisons they make at once. Ch. 21
- Antenna effect
- Charge collected by a long metal wire during plasma etching, before the wire is connected to a diffusion, that can damage the thin gate oxide it ends on. Limited by the antenna rules, a ratio of metal area to gate area. Ch. 17
- Antenna ratio
- The area of a conductor exposed to plasma etching divided by the gate area it connects to; antenna rules limit it to protect thin gate oxides. Ch. 24
- Aperture jitter
- Random variation of the instant at which a sampler takes its sample; for a sine it limits the SNR to \(-20\log_{10}(2\pi f_{in}\sigma_t)\). Ch. 19
B
- Bandgap reference
- A circuit that adds a voltage falling with temperature (\(V_{BE}\), CTAT) to one rising with it (\(\Delta V_{BE}\), PTAT) so that the sum is nearly independent of temperature, about 1.2 V or a scaled version of it. Ch. 14
- Beta multiplier
- A self-biased current reference in which a resistor sets the current through the difference of two gate-source voltages. Its current depends on an absolute resistance and on mobility. Ch. 8
- BiCMOS
- A process with both CMOS transistors and bipolar transistors; SG13G2 adds SiGe HBTs to a 130 nm CMOS process. Ch. 3
- Binned model
- A transistor model made of many parameter sets, each fitted for a small range of W and L; the simulator picks the bin that contains the device. The original SKY130 models are binned. Ch. 3
- Black’s equation
- The empirical median lifetime of a wire under electromigration, \(\mathrm{MTTF} = A\,j^{-n}e^{E_a/kT}\), from which current-density rules and their temperature derating follow. Ch. 24
- Body effect
- The rise of a MOSFET’s threshold voltage when its source is above its body, described by the coefficient γ; in small-signal form, the transconductance \(g_{mb}\). Ch. 4
- Bond wire
- The thin gold or aluminium wire from a pad on the die to a lead of the package. Its inductance, about 1 nH per millimetre, causes supply bounce. Ch. 17
- Bootstrapped switch
- A sampling switch whose gate is driven to \(V_{in} + V_{DD}\) by a capacitor charged to \(V_{DD}\), so that its \(V_{GS}\) and on-resistance hardly change with the signal. Ch. 19
- Bottom-plate capacitance
- The parasitic capacitance from a capacitor’s lower plate to the substrate; connect that plate to the low-impedance node. Ch. 26
- Bottom-plate sampling
- Opening the switch at the fixed-voltage plate of a sampling capacitor slightly before the input switch, so that the sampled charge does not depend on the input switch’s charge injection. Ch. 19
- BSIM4
- The Berkeley short-channel MOSFET model, threshold-voltage based, built into ngspice and used by the SKY130 models. Ch. 3
C
- Cascode
- A transistor in common-gate configuration stacked on another, which multiplies the output resistance by its intrinsic gain at the cost of headroom. Ch. 7
- CDL
- Circuit Description Language, a SPICE-like netlist format for LVS in which devices are written as
M,RandCelements. IHP’s KLayout LVS deck needs its reference in this form. Ch. 16 - Channel-length modulation
- The slow rise of a saturated MOSFET’s current with drain voltage as the pinch-off region shortens the channel; modelled by λ or the Early voltage \(V_A\). Ch. 4
- Charge injection
- The channel charge of a MOS switch that flows onto the capacitor when the switch opens, roughly half of it with a fast clock edge; with clock feedthrough it causes the pedestal. Ch. 18
- Charge pump
- A pair of switched current sources that push charge into, or pull it out of, a loop filter for as long as a phase detector’s UP or DN signal lasts; the average current is \(I_{CP}\Delta\phi/2\pi\). Ch. 22
- Charged-device model (CDM)
- The ESD test in which the charged package itself discharges through one pin in about a nanosecond, with peak currents of several amperes. Ch. 29
- Charge-redistribution DAC
- A DAC of binary-weighted capacitors with joined top plates, whose bottom plates switch between a reference and ground; the DAC inside most SAR ADCs. Ch. 21
- Clock feedthrough
- The coupling of a switch’s gate edge onto its capacitor through the gate-drain overlap capacitance. Ch. 18
- CMRR
- Common-mode rejection ratio, the differential gain divided by the common-mode gain of an amplifier. Ch. 10
- Coherent sampling
- Sampling a sine so that a record of N samples holds exactly M cycles (M odd, N a power of two); the signal and its harmonics then fall on FFT bins without a window. Ch. 19
- Common-centroid layout
- An arrangement of the units of matched devices so that each device’s centre of gravity is at the same point, which cancels linear gradients of process parameters. Ch. 15
- Common-mode input range
- The range of input common-mode voltage over which every transistor of an amplifier stays in saturation. Ch. 10
- Compact model
- The set of equations a circuit simulator uses for a device, with parameters fitted to measurements of the process. PSP and BSIM4 are compact models. Ch. 3
- Comparator
- A circuit that decides which of two inputs is larger and gives a digital output; a clocked comparator decides once per clock period. Ch. 20
- Core-limited die
- A die whose size is set by the area of its circuits rather than by its pad count. Ch. 30
- Corner
- A set of model parameters that shifts the devices to one edge of the expected production spread: fast or slow NMOS and PMOS (ff, ss, fs, sf) around typical (tt). Ch. 3
- Critical dimension (CD)
- The smallest feature a lithography step prints reliably, about \(k_1\lambda/NA\); it sets the minimum widths and spacings of the layers it patterns. Ch. 23
- CTAT
- Complementary to absolute temperature: falling linearly with temperature, like the \(V_{BE}\) of a bipolar transistor at constant current. Ch. 14
- Current mirror
- Two or more transistors with a common gate-source voltage, so that the output current copies the input current scaled by the ratio of their sizes. Ch. 8
- Current-starved VCO
- A ring oscillator whose inverters draw their current through current sources set by the control voltage, so that the stage delay, and the frequency, follow the current. Ch. 22
D
- DAC (digital-to-analog converter)
- A circuit that turns a code into one of \(2^N\) voltages or currents: a resistor string, switched current sources or a capacitor array. Ch. 21
- Dead zone
- A range of small phase errors to which a phase-frequency detector and charge pump give no output, when their pulses are too short to turn the current sources on; avoided with a reset pulse of finite width. Ch. 22
- Delta-sigma modulator
- An oversampling converter that places a coarse quantizer, often of one bit, in a feedback loop with a loop filter, so that the quantization noise is shaped away from the signal band. Ch. 21
- DIBL
- Drain-induced barrier lowering: in a short transistor the drain lowers the barrier at the source and so the threshold voltage, which lowers the output resistance. Ch. 4
- Differential pair
- Two matched transistors with a common tail current, which respond to the difference of their gate voltages and reject their common mode. Ch. 10
- DNL (differential nonlinearity)
- The error of each step of a converter’s transfer curve, in LSB, after offset and gain error are removed. A DNL of −1 LSB is a missing code. Ch. 21
- Dominant pole
- The lowest-frequency pole of an amplifier when it lies far below all others, so that the response is close to first order up to the unity-gain frequency. Ch. 9
- Doublet
- A pole and a zero close to each other, as at the mirror node of the 5T OTA; it causes a small phase dip and a slow settling tail. Ch. 10
- DRC
- Design-rule check, the comparison of a layout’s geometry with the foundry’s rules of width, spacing, enclosure, extension and density. Ch. 16
- Droop
- The change of a held voltage during the hold phase caused by leakage, at a rate \(I_{leak}/C_H\). Ch. 19
- Dummy device
- A transistor, resistor or capacitor drawn only so that the devices next to it see the same surroundings as those in the middle of an array; it carries no signal. Ch. 15
- ΔVBE
- The difference of the base-emitter voltages of two bipolar transistors at different current densities, \(nV_T\ln N\), proportional to absolute temperature: the PTAT term of a bandgap. Ch. 28
E
- Electromigration
- The slow drift of metal atoms pushed by the conduction electrons, which opens voids and grows hillocks in wires and vias that carry too much current density. Ch. 24
- Enclosure rule
- A rule that one layer must extend beyond another by a minimum margin, sized from the physical need plus both layers’ width errors and their misalignment. Ch. 23
- ENOB (effective number of bits)
- The resolution of an ideal converter with the same SNDR as a real one: \((\mathrm{SNDR} - 1.76\ \mathrm{dB})/6.02\ \mathrm{dB}\). Ch. 21
- ESD protection
- Diodes and clamps at every pad that conduct the current of an electrostatic discharge around the core circuit before it can break a gate oxide. Ch. 17
- Extraction
- The step that recognizes devices and nets in a layout (for LVS) and, in parasitic extraction (PEX), adds the resistance and capacitance of the wiring to the netlist. Ch. 16
F
- Fill
- Shapes added to empty areas of a layer so that its local density meets the minimum the polishing steps need. Ch. 17
- Flash ADC
- An ADC that compares its input with all \(2^N - 1\) reference levels at once, with as many comparators: the fastest architecture, limited to a few bits. Ch. 21
- Flicker noise
- Noise whose density falls as \(1/f\), in a MOSFET caused by carriers trapped and released in the oxide; described by \(K_f'\) and inversely proportional to the gate area. Ch. 13
- Flicker-noise corner
- The frequency \(f_c\) at which flicker and thermal noise densities are equal. Ch. 13
- Flip-around sample-and-hold
- A closed-loop sample-and-hold whose sampling capacitor is connected between the amplifier’s output and inverting input in hold; its feedback factor is close to 1. Ch. 19
- Floorplan
- The placement of a die’s blocks, pads and power routing, arranged around noise, heat and matching before detailed layout begins. Ch. 30
- fT
- Transit frequency, the frequency at which a transistor’s current gain falls to one, \(g_m/(2\pi C_{gg})\); a measure of its speed at a given bias. Ch. 5
G
- Gain margin
- How far the loop-gain magnitude is below 0 dB at the frequency where its phase reaches −180°. Ch. 11
- Gate pitch
- The centre-to-centre distance of neighbouring gates in a transistor row: the gate length plus a contacted source or drain between them. Ch. 23
- GBW
- Gain-bandwidth product, the low-frequency gain times the bandwidth of a single-pole amplifier; equal to its unity-gain frequency. Ch. 10
- GDS
- GDSII, the binary file format of a layout: polygons on numbered layers, organized in cells. Ch. 15
- gm/ID
- Transconductance efficiency, the transconductance per unit drain current. It sets the inversion level of a transistor and, with L, all its other properties per unit width, which makes it the design variable of the lookup-table method. Ch. 6
- Guard ring
- A ring of substrate or well contacts around a device or block that collects stray carriers and holds the local substrate potential. Ch. 15
H
- Halo implant
- Extra doping near the source and drain ends of the channel that limits short-channel effects; it makes the threshold of short SG13G2 devices rise and lowers their output resistance. Ch. 3
- HBT
- Heterojunction bipolar transistor; in SG13G2 a SiGe device with an fT of 350 GHz. Ch. 3
- Head resistance
- The resistance of a resistor’s contacted ends (contacts, silicide interface and end film), added twice to the body’s resistance and important in short segments. Ch. 25
- Headroom
- The part of the supply voltage that a stack of transistors needs to keep each one in saturation, which leaves the rest for the signal swing. Ch. 7
- Hold-mode feedthrough
- Coupling of the input to the held voltage through the open switch and, in practice mostly, the wiring capacitance of the layout. Ch. 19
- Human-body model (HBM)
- The ESD test that discharges a 100 pF capacitor through 1.5 kΩ into a pin, imitating a charged person touching the chip. Ch. 29
I
- Ideality factor
- The factor \(n\) in a junction’s exponential law, \(I \propto e^{V/nV_T}\); close to 1 for a good bipolar transistor and set by recombination in a diode. Ch. 28
- IIC-OSIC-TOOLS
- The container image of the Department for Integrated Circuits at JKU Linz with the open-source design tools and PDKs used in this course; release 2026.10. Ch. 2
- INL (integral nonlinearity)
- The distance of each level of a converter’s transfer curve from the straight line through its end points, in LSB; the sum of the DNL up to that code. Ch. 21
- Interdigitation
- An arrangement of the fingers of two matched devices alternately (ABAB, or ABBA), so that they share gradients and surroundings. Ch. 15
- Intrinsic gain
- The voltage gain of a single transistor with an ideal current-source load, \(g_m/g_{ds}\). Ch. 5
- Inversion coefficient
- The drain current divided by the specific current \(I_\mathrm{spec}\); below 0.1 the device is in weak inversion, above 10 in strong inversion. Ch. 6
- IR drop
- The voltage lost along supply wiring by its current times its resistance; a power grid is sized to keep it to a small fraction of the supply. Ch. 30
J
- Jitter
- Random variation of the timing of a clock’s edges. The period jitter is the standard deviation of one period; in a free-running oscillator the timing error accumulates as a random walk. Ch. 22
K
- Kickback
- The disturbance a comparator’s internal voltage swings couple back onto its inputs, and so onto the circuit that drives them. Ch. 20
- KLayout
- The open-source layout viewer and editor, with a scripting interface in Python and Ruby, that runs the DRC and LVS decks of both PDKs. Ch. 2
- kT/C noise
- The noise frozen on a capacitor when a switch opens: \(kT/C\) in variance, independent of the switch resistance. Ch. 13
L
- Latch-up
- The triggering of the parasitic thyristor formed by the wells and diffusions of a CMOS process, which shorts the supply until the power is removed; prevented with taps and guard rings. Ch. 24
- LDO
- Low-dropout regulator, a linear regulator whose pass transistor can work with a small difference between input and output voltage. Ch. 14
- LOD effect
- Length-of-diffusion effect, the change of a transistor’s current with the distance from its gate to the edge of the trench oxide, caused by mechanical stress. Ch. 15
- Loop filter
- The impedance that turns a charge pump’s current pulses into the control voltage of a PLL’s VCO; a resistor in series with a capacitor provides the zero that makes the loop stable. Ch. 22
- Loop gain
- The gain \(T\) around a feedback loop, broken at one point; its magnitude and phase set the accuracy and the stability of the closed loop. Ch. 11
- LSB (least significant bit)
- The step of a converter, \(V_{FS}/2^N\); also the unit in which DNL, INL and offset are given. Ch. 21
- LVS
- Layout versus schematic, the comparison of the circuit extracted from a layout with the reference netlist, device by device and net by net. Ch. 16
M
- Magic
- An open-source VLSI layout tool with its own interactive DRC and a capacitance extractor; used for SKY130 LVS (with Netgen) and for parasitic extraction in both PDKs. Ch. 2
- Metal debiasing
- The loss of drive in a large transistor because its source and drain metal drops voltage along the fingers and buses, so parts of the channel see less than the full bias. Ch. 29
- Metastability
- The state of a latch whose input is so small that it has not resolved to a valid logic level within the time allowed. Ch. 20
- Miller compensation
- A capacitor across the inverting second stage of a two-stage amplifier, which splits its poles: the first moves down, the second up. Ch. 11
- Miller effect
- A capacitor across an inverting gain −A appears at the input multiplied by 1 + A. Ch. 9
- MIM capacitor
- Metal-insulator-metal capacitor, a thin dielectric between a lower metal and an extra metal plate: 1.5 fF/µm² in SG13G2, 2.0 fF/µm² in SKY130. Ch. 3
- Mismatch
- The random difference between devices drawn identically, frozen in when the chip is made. Its standard deviation falls with the square root of the device area. Ch. 13
- Missing code
- An output code that an ADC never produces, because its step has zero width (DNL = −1 LSB). Ch. 21
- Moderate inversion
- The region between weak and strong inversion (inversion coefficient 0.1 to 10), where most low-power analog transistors are biased because it balances efficiency and speed; \(g_m/I_D\) of 10 to 18 V⁻¹ is the usual choice for amplifying devices. Ch. 6
- MOM capacitor
- A metal-oxide-metal capacitor built from interleaved fingers in several metal layers, using lateral fringe fields; it needs no extra mask. Ch. 26
- Monte Carlo simulation
- Repeated simulation with random device parameters drawn from the PDK’s statistical models, to predict the spread of a circuit’s performance. Ch. 13
- MPW
- Multi-project wafer, a run on which the designs of many customers share the cost of the masks; also called a shuttle. Ch. 17
N
- Netgen
- An open-source netlist comparison tool used for LVS with Magic in SKY130. Ch. 2
- ngspice
- The open-source circuit simulator of the course, a descendant of Berkeley SPICE, which loads compiled Verilog-A models through OSDI. Ch. 2
- Noise shaping
- Filtering the quantization error inside a feedback loop so that its spectrum is small in the signal band and large outside it, where a digital filter removes it. Ch. 21
- Non-overlapping clocks
- Two clock phases that are never high at the same time, with a short gap between one falling and the other rising, so that two switches in series are never on together. Ch. 18
- Nulling resistor
- A resistor in series with the Miller capacitor that moves the right-half-plane zero to infinity (\(R_z = 1/g_{m6}\)) or into the left half-plane. Ch. 11
- Number of squares
- The length of a resistor body divided by its width; times the sheet resistance it gives the body’s resistance, with corrections for bends and width bias. Ch. 25
O
- Offset voltage
- The input voltage needed to bring an amplifier’s output to its nominal value; random offset comes from mismatch, systematic offset from the design itself. Ch. 13
- Open-circuit time constants
- A method that estimates the bandwidth of a circuit from the sum of the RC products of each capacitor with the resistance it sees when all others are open. Ch. 9
- OSDI
- Open Source Device Interface, the way ngspice loads compiled Verilog-A models from a shared library, such as SG13G2’s
psp103.osdi. Ch. 3 - OTA
- Operational transconductance amplifier, an amplifier with a high output resistance meant to drive capacitive loads, such as the 5T and the two-stage Miller OTA. Ch. 10
- Overdrive voltage
- \(V_{OV} = V_{GS} - V_{TH}\), the gate voltage above threshold; in strong inversion \(g_m = 2I_D/V_{OV}\). Ch. 4
- Overlay
- The misalignment between two mask layers; with width errors it sets enclosure and extension rules. Ch. 23
- Oversampling ratio (OSR)
- The ratio of a converter’s sampling frequency to twice its signal bandwidth. Each doubling gains 3 dB with white quantization noise, and \(6L + 3\) dB with an L-th-order noise-shaping loop. Ch. 21
P
- Pad ring
- The ring of I/O cells around the core of a chip, each with a bond pad, ESD protection and supply connections. Ch. 17
- Pad-limited die
- A die whose size is set by the number of pads around its edge rather than by the area of its core. Ch. 30
- Parasitic-insensitive integrator
- A switched-capacitor integrator with both plates of its input capacitor switched, so that the parasitic capacitances of its nodes carry no signal charge. Ch. 18
- PDK
- Process design kit, the foundry’s package of models, symbols, parametrized cells, rule decks and documentation that a designer needs to use a process. Ch. 1
- Pedestal
- The step error left on a sampling capacitor when its switch opens, from charge injection and clock feedthrough. Ch. 18
- Pelgrom’s law
- The standard deviation of the mismatch between two devices is inversely proportional to the square root of their gate area, \(\sigma(\Delta V_{TH}) = A_{VT}/\sqrt{WL}\). Ch. 13
- Phase margin
- 180° plus the phase of the loop gain at the frequency where its magnitude is one; 60° or more gives a well-damped step response. Ch. 11
- Phase noise
- The noise power of an oscillator in 1 Hz at an offset from its carrier, relative to the carrier, in dBc/Hz; the frequency-domain view of jitter. Ch. 22
- Phase-frequency detector (PFD)
- Two flip-flops clocked by the reference and the feedback, reset together, whose UP and DN pulses last as long as the phase error; it also drives the loop towards the right frequency. Ch. 22
- Phase-locked loop (PLL)
- A feedback loop that locks a VCO’s divided output to a reference in phase, so that the output frequency is exactly N times the reference. Ch. 22
- Pipelined ADC
- An ADC built as a chain of stages, each resolving a few bits and passing the amplified residue to the next, all working at once on successive samples. Ch. 21
- Pole
- A frequency at which a transfer function’s denominator is zero; each real pole adds 90° of phase lag and a −20 dB/decade slope. Ch. 9
- Post-layout simulation
- Simulation of the netlist extracted from the layout, with the wiring parasitics, using the same testbench as for the schematic. Ch. 16
- PSP
- A surface-potential-based compact MOSFET model written in Verilog-A; SG13G2 uses version 103.6. Ch. 3
- PSRR
- Power-supply rejection ratio, how strongly an amplifier attenuates a signal on its supply relative to its gain for the input. Ch. 12
- PTAT
- Proportional to absolute temperature, like the difference of two \(V_{BE}\) at different current densities. Ch. 14
- PyCell
- A parametrized cell written in Python that draws a device from its parameters; SG13G2’s KLayout PyCells draw its transistors, resistors and capacitors. Ch. 15
Q
- Quality factor (Q)
- The ratio of stored to dissipated energy per cycle of a reactive component, \(\omega L/R_s\) for an inductor; set by metal resistance, skin effect and substrate loss. Ch. 26
- Quantization noise
- The error of an ideal converter, up to half an LSB, treated as a uniform random noise of power \(\mathrm{LSB}^2/12\); it limits the SQNR to \(6.02N + 1.76\) dB. Ch. 21
R
- Rail clamp
- An ESD device between the supply rails, usually a large NMOS triggered by an RC timer, that carries the discharge current once the pad diodes have steered it onto a rail. Ch. 29
- Reference spur
- A tone in a PLL’s output spectrum at the reference frequency’s distance from the carrier, caused by the periodic ripple that the charge pump leaves on the control voltage. Ch. 22
- Regeneration
- Positive feedback in a latch that makes a small voltage difference grow exponentially, \(\Delta V(t) = \Delta V_0\,e^{t/\tau}\), with \(\tau \approx C/g_m\). Ch. 20
- Right-half-plane zero
- A zero with a positive real part, caused in the Miller OTA by the feedforward path through \(C_c\); it adds phase lag like a pole while raising the gain. Ch. 11
- Ring oscillator
- An odd number of inverters in a loop, oscillating at \(1/(2N_st_d)\) for a stage delay \(t_d\). Ch. 22
S
- Sample-and-hold
- A circuit that takes a sample of its input at a defined instant and keeps it constant for a following circuit, usually a data converter. Ch. 19
- Sampled-data circuit
- A circuit that processes one sample of its input per clock period, described by difference equations and the z-transform. Ch. 18
- SAR ADC
- A successive-approximation ADC: a comparator, a DAC and a register find the code by binary search, one bit per decision. Ch. 21
- Saturation (MOSFET)
- The region in which the drain current depends only weakly on the drain voltage, for \(V_{DS} > V_{DS,\mathrm{sat}}\); the region of amplifiers and current sources. Ch. 4
- Saturation voltage
- The lowest drain-source voltage that keeps a transistor in saturation: \(V_{OV}\) in strong inversion, about \(2/(g_m/I_D)\) in general, and a few \(U_T\) in weak inversion. Ch. 4
- Seal ring
- Rings of all metal and via layers around the edge of the die that stop cracks and moisture from the sawing. Ch. 17
- Self-heating
- The temperature rise of a wire or device from its own dissipation, which raises resistance and shortens electromigration life. Ch. 24
- Sheet resistance
- The resistance of a square of a resistive layer, in Ω/□; a resistor of L/W squares has \(R_\square L/W\) plus its end resistances. Ch. 3
- Skin effect
- The crowding of high-frequency current into the surface of a conductor, within a skin depth \(\delta = \sqrt{\rho/(\pi f\mu_0)}\), which raises its resistance. Ch. 26
- Slew rate
- The largest rate of change of an amplifier’s output, set by the current available to charge its capacitors. Ch. 10
- Slope factor
- The factor \(n\) by which the gate’s control of the channel is weaker than ideal, from the capacitive divider of the oxide and the depletion layer; it sets the subthreshold slope. Ch. 4
- Small-signal model
- The linear circuit that describes a device’s response to small changes around its operating point: \(g_m\), \(g_{ds}\), \(g_{mb}\) and the capacitances. Ch. 5
- Snapback
- The drop in voltage of an NMOS or SCR once its parasitic bipolar device turns on under high current; the basis of many ESD devices, and absent from both PDKs’ models. Ch. 29
- SNDR
- Signal-to-noise-and-distortion ratio: the power of a sine at a converter’s output relative to everything else in its spectrum. Ch. 21
- Spurious-free dynamic range (SFDR)
- The ratio of a sine signal to the largest other component of the output spectrum, usually a harmonic. Ch. 19
- Static phase offset
- The time error that a locked PLL keeps between its reference and feedback edges, where the charge pump’s average current is zero despite current mismatch and charge injection. Ch. 22
- STI
- Shallow trench isolation, the oxide-filled trenches that separate the active areas of a process. Ch. 17
- Strong inversion
- The region in which the channel is a sheet of mobile charge proportional to \(V_{OV}\), and the square law holds approximately. Ch. 4
- StrongARM latch
- A dynamic comparator in which an input pair discharges the precharged nodes of two cross-coupled inverters, which then regenerate; it draws no static current. Ch. 20
- Substrate PNP
- The parasitic vertical PNP of a CMOS process: p+ emitter in an n-well base over the p-substrate collector; the bipolar device of SKY130 bandgaps. Ch. 28
- Subthreshold slope
- The gate voltage needed to change a weakly inverted transistor’s current by a factor of ten, \(nU_T\ln 10\). Ch. 4
- Switched capacitor
- A capacitor and two switches clocked in alternate phases; it moves a charge \(C\Delta V\) per period and behaves like a resistor \(1/(f_sC)\). Ch. 18
- Systematic mismatch
- Mismatch with a definite cause and sign, from gradients, stress, wells or asymmetric surroundings; unlike random mismatch, it is removed by layout rather than by area. Ch. 27
- Systematic offset
- The offset of an amplifier with perfectly matched devices, caused by unequal drain voltages or current ratios in the design. Ch. 12
T
- Tape-out
- The release of a design’s final GDS to the foundry. Ch. 17
- Telescopic stage
- A differential or single-ended stage with cascodes on both the input transistors and their loads, for high gain from one stage. Ch. 7
- Thermal gradient
- A temperature difference across a chip caused by a hot block; it shifts threshold voltages and resistances and is cancelled by common-centroid placement and distance. Ch. 27
- Thermal noise
- Noise from the random thermal motion of carriers, with a flat spectrum: \(4kTR\) for a resistor, \(4kT\gamma g_m\) for a MOSFET’s drain current. Ch. 13
- Threshold voltage
- The gate-source voltage at which a MOSFET’s channel forms; in this course extracted by linear extrapolation from the point of steepest slope at a small drain voltage (Eq. 3.1). Ch. 4
- Tian’s method
- A way of finding the loop gain of a closed loop from one voltage and one current injection at the same point, without breaking the DC operating point. Ch. 11
- Tiny Tapeout
- An educational project that puts many small designs on a shared chip, on both SKY130 and SG13G2. Ch. 17
- Total harmonic distortion (THD)
- The power of all the harmonics of a sine together, relative to the signal. Ch. 19
- Track-and-hold
- A sample-and-hold whose output follows the input during the track phase and stays constant during the hold phase. Ch. 19
- Transmission gate
- An NMOS and a PMOS switch in parallel with complementary gate signals, which conduct over the whole signal range between them. Ch. 18
- Trim network
- Resistor segments that switches or fuses add or remove after fabrication, to bring an absolute value within tolerance despite process spread. Ch. 25
- Triode
- The region in which a MOSFET behaves as a voltage-controlled resistor, for \(V_{DS} < V_{DS,\mathrm{sat}}\). Ch. 4
U
- Unity-gain frequency
- The frequency \(f_u\) at which the magnitude of an amplifier’s gain, or of a loop gain, falls to one. Ch. 11
V
- Varactor
- A capacitor whose value is tuned by a voltage, in CMOS usually an accumulation-mode MOS device in an n-well; the frequency control of an LC oscillator. Ch. 26
- VCO (voltage-controlled oscillator)
- An oscillator whose frequency is set by a control voltage; its gain \(K_{VCO}\), in Hz/V, enters the loop gain of a PLL. Ch. 22
- Velocity saturation
- The limit on the speed of carriers in a high lateral field, which makes the current of a short transistor rise more slowly than the square law with \(V_{OV}\). Ch. 4
- Verilog-A
- A language for behavioural and compact models of analog devices; compiled by OpenVAF for ngspice. Ch. 3
W
- Waffle transistor
- A large MOSFET whose gate is drawn as a grid with source and drain diffusions in alternate openings, which packs more gate width per area than parallel fingers. Ch. 29
- Walden figure of merit
- The energy per conversion step of an ADC, \(P/(2^{\mathrm{ENOB}}f_s)\), used to compare converters of different speed and resolution. Ch. 21
- Weak inversion
- The region below threshold, where the current is carried by diffusion and rises exponentially with \(V_{GS}\), and \(g_m/I_D\) reaches its maximum of \(1/(nU_T)\). Ch. 4
- Well proximity effect
- The rise of the threshold voltage of a transistor close to the edge of its well, caused by implant ions scattered from the edge of the resist. Ch. 15
- Width bias
- The difference between the drawn and the effective width of a resistor or transistor, caused by lithography, etch and lateral diffusion; it matters most for narrow devices. Ch. 25