Lab 1

Device Characterization

Measure the threshold, the square-law parameters, the subthreshold slope, the small-signal parameters, fT, the ZTC point and the corner spread of the core transistors.

Contents
Lab 1 at a glance  
Goal Measure the threshold, the square-law parameters, the subthreshold slope, the small-signal parameters, fT, the ZTC point and the corner spread of the core transistors.
Reproduces Chapter 4 (Sections 4.2–4.7, Worked example 4.1) and Chapter 5 (Sections 5.3–5.7, Figures 5.5–5.8)
Time 3 hours
Files labs/lab1: vth_tb, idvg_tb, smallsig_tb, temp_tb, corner_tb (.sch) per PDK; sqlaw_fit.py

Hand calculation

Worked example 4.1 biased an NMOS at 50 µA. Do the same for the PMOS of W/L = 5/0.5 with the square-law parameters of Table 4.2 (SG13G2: µCox = 70 µA/V², \(V_{TH}\) = 0.34 V; SKY130: 60 µA/V², 0.94 V): find \(V_{OV} = \sqrt{2I_D/(\mu C_{ox}W/L)}\) and \(\lvert V_{GS}\rvert = \lvert V_{TH}\rvert + V_{OV}\). Then estimate \(g_m = 2I_D/V_{OV}\) for the NMOS reference device of Worked example 5.1 (VOV = 0.187 V and 0.216 V).

Steps

  1. Threshold. In labs/lab1/sg13g2 (or sky130, after sak-pdk sky130A), run ../../sim.sh vth_tb.sch. Four transistors sit side by side, three NMOS devices of W = 5 µm at Lmin, 0.5 and 2 µm and a 5/0.5 PMOS, each with its drain 50 mV from its source. The NGSPICE block finds the maximum of \(g_m\) and extends the tangent there to zero current, exactly the construction of Figure 4.2. The PMOS is turned upside down (source and bulk at ground, gate at \(-V_G\) through the controlled source Egp) so that one sweep drives all four.
  2. Saturation, the square law and Worked example 4.1. Run ../../sim.sh idvg_tb.sch, then python3 ../sqlaw_fit.py. The testbench prints the gate voltage for 50 µA at L = 0.5 µm and at Lmin, the shift caused by 0.3 V of body bias (M3 has its bulk at −0.3 V) and the subthreshold slopes; the script fits \(\sqrt{I_D}\) against \(V_{GS}\) between 0.1 and 0.4 V above the threshold of step 1, prints µCox and the fitted \(V_{TH}\), and repeats your hand calculation with them.
  3. Small-signal parameters three ways. Run ../../sim.sh smallsig_tb.sch. It finds the 50 µA bias, then extracts \(g_m\), \(g_{ds}\) and \(C_{gg}\) from the operating point, from numerical derivatives and from AC analyses at 1 MHz (Section 5.5), and finally measures \(f_T\) where the current gain \(h_{21} = i_d/i_g\) falls to one. In the GUI, plot db(h21) after the run shows Figure 5.5(a).
  4. Temperature. Run ../../sim.sh temp_tb.sch. It sweeps the gate at −40, 27 and 125 °C and prints the gate voltage where the hot and cold curves cross (the ZTC point) and the change of the 50 µA current at fixed \(V_{GS}\).
  5. Corners. corner_tb.sch holds both devices at the \(\lvert V_{GS}\rvert\) that gives 50 µA in tt (taken from step 2). Run it in all five corners with ../../corners.py corner_tb.sch; divide each current by its tt value to get Figure 5.8.

Checkpoint

Table 18.2. Lab 1 results (W = 5 µm, tt, 27 °C unless stated). Saturation values at |VDS| = VDD/2.

Quantity SG13G2 SKY130
\(V_{TH}\) by extrapolation, NMOS Lmin / 0.5 / 2 µm 0.516 / 0.311 / 0.250 V 0.724 / 0.638 / 0.576 V
\(\lvert V_{TH}\rvert\) by extrapolation, PMOS 5/0.5 0.382 V 0.979 V
Square-law fit µCox, \(V_{TH}\): NMOS / PMOS 5/0.5 286 µA/V², 0.249 V / 70 µA/V², 0.340 V 215 µA/V², 0.595 V / 60 µA/V², 0.941 V
\(V_{GS}\) for 50 µA, NMOS 5/0.5: square law / simulated 0.436 / 0.434 V 0.810 / 0.811 V
\(\lvert V_{GS}\rvert\) for 50 µA, PMOS 5/0.5: square law / simulated 0.718 / 0.718 V 1.347 / 1.347 V
Body effect, \(\Delta V_{GS}\) for \(V_{SB}\) = 0.3 V; \(V_{GS}\) at Lmin 35 mV; 0.516 V 59 mV; 0.754 V
Subthreshold slope, NMOS / PMOS 5/0.5 74 / 74 mV/decade 86 / 79 mV/decade
\(g_m\): op / DC derivative / AC 499.5 / 498.7 / 499.5 µS 473.2 / 473.2 / 473.2 µS
\(g_{ds}\): op / DC derivative / AC; \(C_{gg}\): op / AC 18.91 / 18.95 / 18.91 µS; 20.97 / 20.97 fF 4.529 / 4.529 / 4.529 µS; 16.02 / 16.02 fF
\(f_T\) from \(\lvert h_{21}\rvert\) = 1 / from \(g_m/(2\pi C_{gg})\) 4.12 / 3.79 GHz 5.02 / 4.70 GHz
ZTC point: \(V_{GS}\), \(I_D/W\) 0.539 V, 23.5 µA/µm 0.934 V, 24.7 µA/µm
50 µA bias at fixed \(V_{GS}\): change at 125 °C / −40 °C +23 % / −21 % +20 % / −22 %
NMOS current in ss / ff, relative to tt (\(\Delta V_{TH}\)) 0.57× / 1.57× (+47 / −46 mV) 0.74× / 1.32× (+21 / −22 mV)
sf corner: NMOS / PMOS current relative to tt 0.77× / 1.15× 1.44× / 0.70×

The DC-derivative \(g_m\) of SG13G2 is 0.16 % low because smallsig_tb differentiates over only three points 1 mV apart; widen the sweep to 21 points, as Section 5.5 does, and it agrees with the other two to four digits. The leakage at \(V_{GS} = 0\) that idvg_tb also prints (ioff_n) is not in the table: at a fraction of a picoampere it depends on the simulator’s convergence settings as much as on the model.

Questions

  • The SG13G2 NMOS threshold rises by 266 mV from L = 2 µm to Lmin, the SKY130 one by 148 mV. Which effect of Section 4.6 is this, and why does it make it dangerous to mirror a minimum-length device into a long one?
  • Your PMOS hand value of step 2 agrees with the simulation to the millivolt, while the minimum-length NMOS of Worked example 4.1 was 172 mV off in SG13G2. What is different about the two predictions?
  • \(g_m/(2\pi C_{gg})\) is 8 % (SG13G2) and 6 % (SKY130) below the \(f_T\) of the AC measurement. Which current, ignored by that definition, flows into the drain at high frequency?
  • In SG13G2 the letters sf make the NMOS slow; in SKY130 they make it fast. How would you find out which is which for a third PDK, with one testbench and one run of corners.py?

Extension

Add a 5/0.5 PMOS to temp_tb.sch (upside down, as in idvg_tb) and find its ZTC point. Then change vth_tb.sch to the lengths 0.13, 0.25, 0.5, 1, 2 and 5 µm (0.15 µm instead of 0.13 µm in SKY130) and plot \(V_{TH}\) against L to reproduce Figure 4.7(a), including the PMOS that behaves differently in the two processes.


Back to top

SkillSurf · The Art of Analog IC Design, draft v0.1 (November 2026). Every source is listed on the References page.

© 2025–2026 SkillSurf. Text, figures and 3D models: CC BY 4.0; code: MIT. The SkillSurf name and logo are not covered.

This course was written with the help of AI tools and may contain mistakes. If you find one, please tell us through SkillSurf or email skillsurfedu@gmail.com, and we will correct it.

This site uses Just the Docs, a documentation theme for Jekyll.