Lab 5

The 5T OTA

Build Chapter 10's five-transistor OTA as a subcircuit and verify its hand design: gain, bandwidth, phase margin, slew rate, input range, offset and power.

Contents
Lab 5 at a glance  
Goal Build Chapter 10’s five-transistor OTA as a subcircuit and verify its hand design: gain, bandwidth, phase margin, slew rate, input range, offset and power.
Reproduces Chapter 10 (Sections 10.5–10.8, Tables 10.1 and 10.2, Figures 10.6 and 10.7)
Time 2–3 hours
Files labs/lab5: ota5t.sch and ota5t.sym (the OTA), ota5t_ac_tb, ota5t_tran_tb, ota5t_icmr_tb (.sch) per PDK

Hand calculation

From Table 10.1: \(g_{m1}\) = 320 µS and \(I_{tail}\) = 40 µA into \(C_L\) = 2 pF. Predict the GBW, \(g_{m1}/(2\pi C_L)\), and the slew rate, \(I_{tail}/C_L\). With the gate voltages of Table 10.1, evaluate Eq. (10.12) for the input common-mode range.

Steps

  1. Open the OTA. ota5t.sch is the OTA of Table 10.1 with six ports (vdd, vss, inp, inn, out, ibias), and ota5t.sym is its symbol. In the GUI, select the symbol in a testbench and press e to descend into the schematic, Ctrl+e to come back. Every testbench of this lab instantiates it as x1, so its internal nodes are x1.n1, x1.tail and its devices x1.xm1 and so on.
  2. Gain, bandwidth, phase margin. Run ../../sim.sh ota5t_ac_tb.sch. As in Section 10.8, a 1 GH inductor closes the unity-gain loop at DC only and a 1 F capacitor grounds the inverting input for AC, so the AC analysis shows the open-loop gain at the buffer’s operating point. The testbench also prints the systematic offset and the power, including the 10 µA reference.
  3. Slew rate. Run ../../sim.sh ota5t_tran_tb.sch: two buffers, one with a 300 mV step and one with a 20 mV step around \(V_{ic}\). It prints the steepest rising and falling slopes of the large step and the final value of the small step as a fraction of the step. plot v(in1) v(out1) shows Figure 10.7(a).
  4. Input range. Run ../../sim.sh ota5t_icmr_tb.sch. It sweeps the buffer input and computes the saturation margins \(V_{DS} - V_{DS,sat}\) of M1 and M5 from their operating points; the ICMR is where both are positive. plot m1 m5 shows Figure 10.6(a).

Checkpoint

Table 18.6. Lab 5 results (unity-gain buffer at Vic = 0.70 V and 1.10 V, CL = 2 pF, tt, 27 °C).

Quantity SG13G2 SKY130
DC gain, GBW, phase margin 26.2 dB, 23.8 MHz, 87° 41.7 dB, 24.5 MHz, 85°
Systematic offset, power −1.07 mV, 59.7 µW −4.31 mV, 87.9 µW
Slew rate, rising / falling 20.4 / 17.7 V/µs 19.4 / 21.9 V/µs
20 mV step: final value / step 0.951 0.987
Input common-mode range 0.49–0.91 V 0.87–1.30 V

Questions

  • The final value of the small step is 0.951 in SG13G2. Show that this is \(A_0/(1 + A_0)\) for your DC gain. What does it say about using this OTA as a buffer?
  • Why do the rising and falling slew rates differ, and why in opposite directions in the two PDKs?
  • The SKY130 OTA has 50 % more supply but barely more input range. Where does the extra 0.6 V go?

Extension

Change the length of M3 and M4 in ota5t.sch to 2 µm (keep the width) and rerun ota5t_ac_tb: the gain should rise by less than 1 dB while the phase margin falls (Section 10.8, step 4). Then move \(V_{ic}\) to mid-supply in ota5t_ac_tb and find out from the operating point (print @n.x1.xm1.nsg13_lv_nmos[vdss] in SG13G2, @m.x1.xm1.msky130_fd_pr__nfet_01v8[vdsat] in SKY130, and the node voltages) which transistor leaves saturation first.


Back to top

SkillSurf · The Art of Analog IC Design, draft v0.1 (November 2026). Every source is listed on the References page.

© 2025–2026 SkillSurf. Text, figures and 3D models: CC BY 4.0; code: MIT. The SkillSurf name and logo are not covered.

This course was written with the help of AI tools and may contain mistakes. If you find one, please tell us through SkillSurf or email skillsurfedu@gmail.com, and we will correct it.

This site uses Just the Docs, a documentation theme for Jekyll.