Cover of RFIC Design with Open-Source Tools: an orange impedance trace crossing the centre of a Smith chart, above an oscillator spectrum, on dark navy

SkillSurf · IHP SG13G2 SiGe BiCMOS

RFIC Design with Open-Source Tools

An open-source course in radio-frequency integrated-circuit design, from the transistor to the transceiver. Every circuit is designed and simulated with free tools in an open 130 nm SiGe BiCMOS process whose transistors reach 300 GHz.

Start reading Chapter 1 Course plan

SG13G2IHP's open SiGe BiCMOS PDK
~300 GHzSiGe HBT fT
2.4 GHzcourse transceiver
50 GHzmillimetre-wave amplifier
19chapters in six parts

Every phone, watch, car key and Wi-Fi router holds a radio, and the heart of each one is a radio-frequency integrated circuit: a low-noise amplifier that hears a signal a billion times weaker than a milliwatt, a mixer that moves it to a frequency a converter can handle, an oscillator locked to a crystal by a phase-locked loop, and a power amplifier that sends a reply. Designing these circuits used to need commercial simulators, electromagnetic solvers and process data behind non-disclosure agreements. Today an open process, IHP’s SG13G2 SiGe BiCMOS technology, and open tools (ngspice, Xyce, openEMS, Palace, KLayout and Python) cover the whole path from specification to layout.

This course teaches RFIC design on that open stack. It follows one method throughout: the physical idea, a short derivation, a hand calculation, then a simulation with the PDK’s own models, closed by a what this means for your design box. Every plot and number comes from a script in this repository, so you can reproduce, change and extend it.

What is inside

Part I · Ch 1–5

RF fundamentals

What makes RF different, simulating RF circuits with open tools, S-parameters and the Smith chart, noise and linearity, modulation and transceiver architectures.

Part II · Ch 6–8

Devices and passives

MOSFETs and SiGe HBTs at gigahertz frequencies, spiral inductors, capacitors, varactors and transmission lines, and impedance matching.

Part III · Ch 9–11

The receiver

Low-noise amplifiers, mixers and LC oscillators, each designed for the course's 2.4 GHz radio.

Part IV · Ch 12–15

Frequency synthesis

PLL dynamics and phase noise, frequency dividers, fractional-N synthesizers and digital PLLs.

Part V · Ch 16–17

The transmitter

Power amplifier classes, efficiency and linearity, and a 50 GHz SiGe power amplifier from bias point to electromagnetic simulation.

Part VI · Ch 18–19

From silicon to system

RF layout and electromagnetic verification, and the complete transceiver.

Appendices

Reference

Formula sheet, RF simulation cheat sheet, SG13G2 RF device reference and a glossary.

One process, built for radio

The course is built on IHP SG13G2, a 130 nm SiGe:C BiCMOS process with an open PDK: 1.2 V and 3.3 V CMOS, heterojunction bipolar transistors with fT and fmax around 300 GHz, MIM capacitors, varactors, and two thick top metals for inductors and transmission lines. Where the comparison teaches something, the same circuit is also simulated with the CMOS transistors of SkyWater SKY130, the other open 130 nm process; plots show SG13G2 in blue and SKY130 in amber.

The course radio

The chapters design the blocks of one radio: a 2.4 GHz transceiver for the licence-free ISM band, in the style of Bluetooth Low Energy. Part III builds its receiver (low-noise amplifier, quadrature mixer and LC VCO), Part IV the fractional-N synthesizer that tunes it across the band, Part V its power amplifier, and Part VI puts the pieces together. A second project, a 50 GHz SiGe power amplifier in Chapter 17, follows a design from the IHP Analog Academy into millimetre-wave territory, where every wire is a transmission line.

Where this course starts

This course assumes the analog design background of SkillSurf’s The Art of Analog IC Design: transistor models, gm/ID sizing, amplifiers, feedback and noise. Part IV continues exactly where that course’s PLL chapter stops.

About

The course is written by SkillSurf. Its scope and sequence draw on Prof. Harald Pretl’s Radio-Frequency Integrated Circuits course at JKU Linz, Prof. Sam Palermo’s ECEN 620 course on phase-locked loops at Texas A&M, the IHP Analog Academy and the classic textbooks of Razavi, Lee and Pozar. All text and figures are original; every source is listed on the References page.

How this course was made. It was developed with the help of AI tools. The text, figures and code are reviewed by the authors, but errors may remain. If you spot one, please tell us through SkillSurf.

This is a living draft (v0.1, November 2026); chapters marked In progress are being written. Corrections and suggestions are welcome through SkillSurf.


Back to top

SkillSurf · RFIC Design with Open-Source Tools, draft v0.1 (November 2026). Every source is listed on the References page.

This course was written with the help of AI tools and may contain mistakes. If you find one, please tell us through SkillSurf or email skillsurfedu@gmail.com, and we will correct it.

This site uses Just the Docs, a documentation theme for Jekyll.